TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was created by two guys in California. They wanted to create a cool writing instrument that looked like a genuine pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.
The Smok Pen has a built quality that’s just great. I came across that even though it can be an electronic pen the construction is just as good as any of the pens that I have reviewed. The reason being of how they made the most notable cap. You don’t need to be worried about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens is the form of the coils and just how that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this on purpose, to make the pen feel more substantial.
Invest the a look at a Smok Pen, you will observe that the body of the pen is round rather than smooth like other pens. On the trunk of the pen there exists a little tab that houses the coil. Once you press on the tab you can actually turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever Personally i think like smoking.
To use the Smok Pen you should keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature you can turn off the heating element. Smok podsmall.com recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
When you put your Smok Pen in to the tank you will see a indicator light seriously. The indicator light will stay green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. You should always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.
After you have completed this step, you should always check to see in case you are at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. For anyone who is still not satisfied together with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the following two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.
Before you go any further you should remove the battery from your pen and unscrew the magnetic cap. You should then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. After you have loosened this wire you can then access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch any of the coils.
Once you have placed the sub-ohm tank into the pen you should then place all of those other components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set you then should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it needs to reach you need to then connect the two wires to the positive and negative on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to underneath of the Smok’s power switch.
After all the components have been placed into the pen, you should turn the energy on. After the first test run, you should be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a brand new one. For your convenience gleam green light that may be pressed to be able to confirm the battery charging status. When you have done these things and you do not see the green light indicating charging, you need to replace the battery.